Navgunner Posted May 24 Report Share Posted May 24 (edited) I’m at the tail end of testing my new sears and new trigger bars (solid one piece) for the S&W76 / MK760 subs. These should be available in a few weeks on my website https://navgunner.com/navgunner-llc . These are precision manufactured from steel alloy (with proper heat treat). Quality parts are expensive to produce so expect these to cost $125 each. I would really like to have found an alternative solution to the rivets (the trigger bar to trigger & the trigger to lower receiver) but I haven’t been able to find an alternate solution that I’m happy with so I’m sticking with rivets. That being said, I’m happy to provide a service to install a new sear, new sear spring, new one-piece trigger bar and new rivets for an extra $150 (this includes USPS Priority shipping back to the customer). You buy the parts for me on my website, check the “I want the service” tab and send me your lower. That’s basically a complete rebuild of your lower for about $400. what are your thoughts? Respectfully, NAV Edited May 24 by Navgunner 3 Quote Link to comment Share on other sites More sharing options...
MontanaRenegade86 Posted May 24 Report Share Posted May 24 Having cobbled together some of these critical 76/760 parts over the past couple of years, I can say this with absolute certainty: Nobody (and I mean nobody) is going to find a better deal than this. You, sir, are a Godsend to the NFA Community. -KristopherH 1 1 Quote Link to comment Share on other sites More sharing options...
Navgunner Posted May 24 Author Report Share Posted May 24 Thank you, @MontanaRenegade86! Without your support, I’m not sure that this would’ve happened. You sir, are a blessing! 1 1 Quote Link to comment Share on other sites More sharing options...
Don. Posted May 26 Report Share Posted May 26 I’m definitely in for one. I’ll see if my buddy is interested. Any chance of selling the rivets as well? Thanks for making these parts available! 1 Quote Link to comment Share on other sites More sharing options...
Bill in Bama Posted May 26 Report Share Posted May 26 Austin, once again you have stepped into the breech to provide a much needed part/service to the MG community. Thanks! 2 Quote Link to comment Share on other sites More sharing options...
MPFiveO Posted May 26 Report Share Posted May 26 Following because I just might want to have one in the spare parts box. 1 Quote Link to comment Share on other sites More sharing options...
Navgunner Posted May 26 Author Report Share Posted May 26 6 hours ago, Don. said: … Any chance of selling the rivets as well? Thanks for making these parts available! It’s best if the rivets are made to fit to each individual lower so I’m reluctant to offer the rivers by themselves. 1 Quote Link to comment Share on other sites More sharing options...
Navgunner Posted May 26 Author Report Share Posted May 26 Quote Link to comment Share on other sites More sharing options...
Caribraddoc Posted May 27 Report Share Posted May 27 NavGunner, I am definitely in for one. Much needed service, thank you Andy 1 Quote Link to comment Share on other sites More sharing options...
StrangeRanger Posted May 27 Report Share Posted May 27 The trigger to lower receiver rivet can be replaced by a grooved pin made from #26 drill rod held by a pair of McMaster -Carr #94981A130 retaining rings or by a headed pin turned from 1/4 drill rod and one retaining ring. PM me your email and I'll send you my drawing Quote Link to comment Share on other sites More sharing options...
MontanaRenegade86 Posted May 31 Report Share Posted May 31 Get ready, guys. As of this morning, I can say.....these two items are going to be HOT. Fantastic job, @Navgunner!!! -KristopherH 1 1 Quote Link to comment Share on other sites More sharing options...
KickStand Posted May 31 Report Share Posted May 31 3 hours ago, MontanaRenegade86 said: Get ready, guys. As of this morning, I can say.....these two items are going to be HOT. Fantastic job, @Navgunner!!! -KristopherH Smalls, you’re a day behind me. Can’t wait for your results! 1 Quote Link to comment Share on other sites More sharing options...
john Posted June 10 Report Share Posted June 10 I'm in for one. Scott Andrey went through my lower a few years ago and gun still runs well so these parts will go on the shelf for whenever needed. I'd be interested in pins with c-clips as Strangers get describes, but have some experience with rivets too so if you decide to include I'd be okay with that too. The rivets look like hollow type.......that the case? John Quote Link to comment Share on other sites More sharing options...
Navgunner Posted June 10 Author Report Share Posted June 10 26 minutes ago, john said: I'm in for one. Scott Andrey went through my lower a few years ago and gun still runs well so these parts will go on the shelf for whenever needed. I'd be interested in pins with c-clips as Strangers get describes, but have some experience with rivets too so if you decide to include I'd be okay with that too. The rivets look like hollow type.......that the case? John The rivets that I make are drilled on one side to help aid the end to flare outwards, this is very similar to the original. I’m only making rivets for customers that want me overhaul their lower. Another option for the install is John Andrewski (he does very good work). I have no intention of making e-clipped pins because I have concerns as it relates to fitment and safety. 2 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.