andrew88 Posted August 27, 2020 Report Share Posted August 27, 2020 (edited) Item for sale -a Group Industries full auto lower model M16A1 Serial number A0104. This lower was purchased in 2013 from a collector in Oregon. These lowers are made of stainless steel Not aluminum. They will last forever. All holes were refilled and tapped by Machine Gun Joe. This lower comes with an LWRC upper receiver and everything you see in the pictures. It runs well. Asking $32,000. Buyer pays $200 transfer cost and UPS shipping costs, including insurance. 100% payment starts transfer process, from Colorado, on Form 4. Sorry, not interested in trades at this time. Edited August 28, 2020 by andrew88 added pictures Link to comment Share on other sites More sharing options...
wastedimage Posted August 27, 2020 Report Share Posted August 27, 2020 Hey Andrew the pictures did not attach. Link to comment Share on other sites More sharing options...
David Albert Posted August 27, 2020 Report Share Posted August 27, 2020 andrew88, Please post photos of the item, and detail why your IP address is in Louisiana versus your stated location of Colorado. I'm sure there may be a good reasons for this, but you are a new member posting a very expensive item, and potential buyers will want to know. Thanks, David Albert Link to comment Share on other sites More sharing options...
andrew88 Posted August 28, 2020 Author Report Share Posted August 28, 2020 I have tried to post the pictures but for some reason they will not and i have contacted the admin to help me get them up. As to the reason my IP shows Louisiana is because that is where I am from and I am currently at home visiting my family and using their computer to make the initial post . I will be back in Colorado this weekend. Link to comment Share on other sites More sharing options...
tal35 Posted August 28, 2020 Report Share Posted August 28, 2020 What does this mean? Was there a problem with the holes? " All holes were refilled and tapped by Machine Gun Joe " Link to comment Share on other sites More sharing options...
eMGunslinger Posted August 28, 2020 Report Share Posted August 28, 2020 I can personally vouch for the owner and the rifle. I’ve sold probably 50k worth of high end bolt guns of his over the years and he’s been a close personal friend of mine for over a decade. I’ve also done some work on this lower before it was sent off to get the entire thing redone. Link to comment Share on other sites More sharing options...
andrew88 Posted September 1, 2020 Author Report Share Posted September 1, 2020 A lot of these receivers were apparently shot extensively when they were in service. Many of them had “egged out” holes. Figured I would keep it for a while so I had machine gun Joe do the work to pair them. Link to comment Share on other sites More sharing options...
trilogymac Posted September 1, 2020 Report Share Posted September 1, 2020 Myself and a friend each have one of these lowers. Many of the hole locations were out of spec. My buddy had his corrected by welding and relocating the holes. I got lucky and mine is good except for the buffer retainer hole. It is about .020 short. Nice that you had yours brought up to spec. These are GREAT lowers!!!!! Hope this helps and good luck with the sale!! Link to comment Share on other sites More sharing options...
Gaffshot Posted September 1, 2020 Report Share Posted September 1, 2020 I have a Group Ind. lower myself. They are fantastic. Stainless steel so will last forever. Nice mg. Good luck with sale. Link to comment Share on other sites More sharing options...
MWT Posted September 16, 2020 Report Share Posted September 16, 2020 What is the caliber registered on this weapon as? I have seen several with N/A and then others with 223. Link to comment Share on other sites More sharing options...
andrew88 Posted September 17, 2020 Author Report Share Posted September 17, 2020 Hi MWT- nothing is stamped on the receiver but paperwork says .223. Link to comment Share on other sites More sharing options...
Recommended Posts